Our Precision Tune-Ups offer the best scheduled service value in the Lee’s Summit area. Regular maintenance on your heating and cooling system will prolong the life of your home comfort system, increase your system’s efficiency, and ensure your system runs through peak seasons without breaking down.

With a One Hour Precision Tune-Up, a highly trained technician will perform these tasks at your home…

  • A/C PRECISION TUNE-UP 44-Point A/C and Safety Inspection (Included with Comfort Club)
  • $139$89
  • Inspect Thermostat Operation
  • Replace Filter with Premium MERV8 Filter
  • Inspect Temperature Split
  • Inspect Disconnect
  • Inspect Fuses (If Applicable)
  • Inspect Wiring
  • Tighten Electrical Connections
  • Inspect Contactors, Relays, Pressure Controls
  • Inspect Electrical Safety Circuits
  • Inspect Voltage and Amperage to All Motors
  • Inspect Blower and Motor for Dirt Buildup
  • Inspect Bearings and Lubricate
  • Inspect Condensate Drain and Clear
  • Inspect Outdoor Coil for Fouling or Damage
  • Inspect Ducts Within 5′ of Furnace for Leakage
  • Test System Operation
  • Inspect Capacitor
  • Determine Start Assist Needs
  • Measure Voltage Drop Across Contactor
  • Measure High Side Pressure
  • Measure Low Side Pressure
  • Measure Superheat or Subcool
  • Inspect for Refrigerant Leaks
  • Inspect O-Ring Schrader Caps
  • Verify Circuit Breaker Size and Nameplate
  • Verify Proper Wire Size to Unit
  • Ensure Condensing Unit is Level
  • Trim Shrubbery around Condensing Unit
  • Inspect Line Set Insulation
  • Inspect and Chemically Clean Condenser Coil
  • Verify Pan Treatment Installed
  • Inspect Blower Capacitor Value
  • Measure Static Pressure of Supply
  • Measure Static Pressure of Return
  • Verify Return Drop Size
  • Inspect Ductwork Cleanliness
  • Ensure Boots Sealed to Floor
  • Inspect and Chemically Clean Indoor Coil
  • Inspect TXV
  • Verify Proper Bulb Mounting
  • Clean and Polish Condensing Unit
  • FURNACE PRECISION TUNE-UP 44-Point Furnace and Safety Inspection (Included with Comfort Club)
  • $139$79
  • Inspect Thermostat Operation
  • Replace Filter with Premium MERV8 Filter
  • Inspect Temperature Rise Across Heat Exchanger
  • Inspect Service and Safety Switches
  • Inspect Wiring
  • Tighten Electrical Connections
  • Inspect Relays, Pressure Switches, Limit Switches
  • Inspect Circuit Board
  • Inspect Voltage and Amperage to All Motors
  • Inspect Blower and Motor for Dirt Buildup
  • Inspect Bearings and Lubricate
  • Inspect Condensate Drain and Clear
  • Inspect Exhaust Flue
  • Inspect Ducts Within 5′ of Furnace for Leakage
  • Test System Operation
  • Measure Carbon Monoxide Level
  • Inspect Blower Cabinet Insulation
  • Clean Burner Tips of Buildup
  • Vacuum Furnace Interior and Area
  • Clean Combustion Air Vent Screen
  • Inspect Heat Exchanger for Cracks and Wear
  • Inspect Hoses for Cracks and Wear
  • Verify Proper Flue Rise at Furnace
  • Verify Proper Flue Rise at Hot Water Heater
  • Inspect Ignitor ohms
  • Inspect and Clean Flame Sensor
  • Measure Flue Clearances and Combustibles
  • Test Gas Connections for Leaks
  • Test Gas Shutoff Operation
  • Verify Circuit Breaker Size and Nameplate
  • Verify Proper Wire Size and Isolation of Circuit
  • Ensure Furnace is Level
  • Verify No Combustibles Within 6′ of Furnace
  • Verify Correct Blower Capacitor
  • Inspect Voltage and Amperage to Inducer Motor
  • Verify Proper Operation of Pressure Switch
  • Inspect and Adjust Gas Pressure at Gas Valve
  • Inspect and Chemically Clean Indoor Coil
  • Verify Carbon Monoxide Detector Installed and Tested
  • Verify Surge Protection Installed
  • Clean and Polish Furnace
  • A/C STANDARD INSPECTION 16-Point Safety Inspection
  • $79$48
  • Inspect Thermostat Operation
  • Replace Filter with Premium MERV8 Filter
  • Inspect Temperature Split
  • Inspect Disconnect
  • Inspect Fuses (If Applicable)
  • Inspect Wiring
  • Tighten Electrical Connections
  • Inspect Contactors, Relays, Pressure Controls
  • Inspect Electrical Safety Circuits
  • Inspect Voltage and Amperage to All Motors
  • Inspect Blower and Motor for Dirt Buildup
  • Inspect Bearings and Lubricate
  • Inspect Condensate Drain and Clear
  • Inspect Outdoor Coil for Fouling or Damage
  • Inspect Ducts Within 5′ of Furnace for Leakage
  • Test System Operation
  • FURNACE STANDARD INSPECTION 16-Point Safety Inspection
  • $79$48
  • Inspect Thermostat Operation
  • Replace Filter with Premium MERV8 Filter
  • Inspect Temperature Rise Across Heat Exchanger
  • Inspect Service and Safety Switches
  • Inspect Wiring
  • Tighten Electrical Connections
  • Inspect Relays, Pressure Switches, Limit Switches
  • Inspect Circuit Board
  • Inspect Voltage and Amperage to All Motors
  • Inspect Blower and Motor for Dirt Buildup
  • Inspect Bearings and Lubricate
  • Inspect Condensate Drain and Clear
  • Inspect Exhaust Flue
  • Inspect Ducts Within 5′ of Furnace for Leakage
  • Test System Operation
  • Measure Carbon Monoxide Level